Model MD-HC41-5 Thin Pass-Through Type Proximity Sensor for Steel Pachinko Balls (Open Collector Output / Shield Type/ 5 V DC)
- Product catalog download
- 3D PDF Download
- MD-HC41-5_EN Download the CAD data (DXF / Parasolid / STEP / IGES)
Application
- Steel material pachinko ball detection.
Features
- The 2-wire sensor requires an external output residual voltage processing circuit and an open collector output conversion circuit (interface IC, etc.).
Since this sensor has these circuits built-in, the cost of the external circuit of the sensor can be significantly reduced. In addition, since this sensor has an open collector output, High / Low logic processing is possible, and it can be directly connected as an input signal of 30 V DC or less. - Ultra-thin type with a thickness of 4 mm.
- Steel material pachinko balls can be counted even when passing in an unbroken consecutive line.
- Since the C-cut shape is used for the main body case, it is possible to prevent incorrect installation orientation.
- A transparent cover allows easy check of the internal condition.
- Features a keyway on the case side for an easy installation in one touch.
- Combined use with EWD-271 (radio wave sensor) gives greater safety against radio interference.
International Standards
- Our products do not have overseas safety regulations such as CE mark, UL standard, EN standard etc.
- Products is compliant to the RoHS directive.
* Please consult about "change of specification" and "request of specification" of the product.
Rating/Performance
Rating / Performance
| Model | MD-HC41-5 | |
|---|---|---|
| Range of Detection | 4.5 to 7.5 mm (* Refer to "Characteristics") | |
| Hysteresis | 0.4 to 1.5 mm or more (* Refer to "Characteristics") | |
| Standard Detection Object target | Steel Pachinko ball (ø 11 ± 0.05 mm) | |
| Power Voltage | 5 V DC (Operating voltage range : 4.7 V to 5.5 V DC) | |
| Power Consumption | 15 mA DC or less | |
| Output Capacity | NPN transistor open collector 30 V DC, 20 mA DC or less | |
| Output Residual Voltage | 1 V DC or less (Load current 20 mA DC) | |
| Operation Status | Normally closed (At detection: output OFF) | |
| Resolution | Balls passing continuously can be detected | |
| Response Frequency | 100 Hz or more | |
| Temperature Range | -10 to 70 °C (Without dew condensation or freezing) | |
| Humidity Range | 35 to 85 % RH (Without dew condensation or freezing) | |
| Vibration Resistance | Durability : 10 to 55 Hz, Double amplitude: 1.5 mm in X-, Y-, and Z-direction, each 2 hours (Device not powered) | |
| Shock Resistance | Durability : 500 m/s² (Approx. 50 G) in X-, Y-, and Z-direction, each 10 times (Device not powered) | |
| Breakdown Voltage | 500 V AC, 50/60 Hz for 1 min (Between live parts and casing) | |
| Insulation Resistance | 50 MΩ or more, at 500 V DC megger (Between live parts and casing) | |
| Anti-static Electricity | Between the outer cover (pachinko ball passage hole) and connector No. 1 terminal (GND) ± 15kV (C = 150pF, R = 330Ω) | |
| Ingress Protection | IP50 | |
| Case Material | Case : PBT resin with glass (Black), Cover : ABS resin (Transparent) | |
| Connector | Connector : DF14A-3P-1.25H(22) (3-pin) (from HIROSE ELECTRIC CO., LTD.) [Connections] Housing : DF14-3S-1.25C, Contact : DF14-2628SCF (from HIROSE ELECTRIC CO., LTD.) |
|
| Weight | Approx. 1.9 g | |
| Options (Sold Separately) |
Connector harness : CNH-DF1403S26-300 | |
Dimensions/Connector Harness/Output Circuit/Characteristics
Dimensions
Connector Harness (Sold Separately)
Output Circuit
*Because there is no reverse connection protection diode built-in, pay careful attention to the polarity of the power supply.
Characteristics
- Range of detection
The pachinko ball is inserted from the IN side, and the distance from the detection point to the point where the detection point changes to non-detection is set as the detection range.
- Hysteresis
The pachinko ball is inserted from the IN side, the pachinko ball is moved in the opposite direction to the insertion from the point to be detected, and the distance from the point where the detection is changed to the non-detection is used as the hysteresis.
Precautions During Use
Influence by Surrounding Metals
Avoid metals in the surroundings, within 3 mm of the detection side and back side of the proximity switch. Otherwise, the range of detection may increase or other malfunctions may occur.
Mutual Interference
When using multiple sensors adjacent to each other, use them at intervals greater than the values shown in the figure below to prevent mutual interference. (The different frequency model type has “B” at the end of its model designation.)
Others
- This sensor is a dedicated detection sensor for steel pachinko balls.
Do not use this sensor as it cannot detect SUS pachinko balls. - Be sure to insert and remove the connector horizontally.
If you insert or remove it at an angle, it may cause terminal deformation, case damage, or poor contact.
For other precautions, refer to "General Precautions" for proximity sensors.
Quote / Order
Quote / Order
Please contact our sales.
