• センサ、タッチセンサの日本語ページ
  • sensor,touch sensor English site
How It Works Shipping Fee Terms of Use

Model MGP-C☐501☐ High-sensitivity electromagnetic sensor NEW 

Application

  • Magnet detection
  • Automatic guided vehicles guidance

Features

  • A DC 3-wire type is also available.
  • N pole detection models and S pole detection models are available. Select the model depending on your usage.
  • Operation can be easily checked with the operation display light.

International Standards

  • Our products do not have overseas safety regulations such as CE mark, UL standard, EN standard etc.
  • Products is compliant to the RoHS directive.

* Please consult about "change of specification" and "request of specification" of the product.

Rating and performance

Rating and performance

Model name MGP-CN5013 MGP-CN5014 MGP-CS5013 MGP-CS5014
Detection surface Front side detection
Detection sensitivity 500 μT ±100 μT
Power supply voltage 12 V to 24 V DC (Operating voltage range: 10 V to 30 V DC)
Power consumption DC 20 mA or less
Output P-channel MOSFET Open drain DC 30 V DC 50 mA or less
Output residual voltage DC 1 V or less ( load current DC 50 mA )
Operation configuration Normally open
(On output
with magnetic field)
Normally closed
(Off output
with magnetic field)
Normally open
(On output
with magnetic field)
Normally closed
(Off output
with magnetic field)
Operation display Red LED (lit when On output)
Response time 300 μs or less
Hysteresis 30 μT or less (with a rubber plate magnet of 30 x 30 x t1.5 mm)
Detection polarity N pole S pole
Reference detection distances 53 mm (*the MG50-1 series)
Operating set distance 5 to 37 mm (*the MG50-1 series)
Operating temperature range -10 to 60 °C (-20 to 65 °C during storage)
(Without dew condensation or freezing)
Operating humidity
range
90% RH or less (90% RH or less during storage)
(Without dew condensation)
Withstand voltage 1 min at AC 500 V 50/60 Hz (between the live part and case)
Insulation resistance 100 MΩ or more measured with an ohmmeter at DC 500 V
(between the live part and case)
Vibration resistance Durability: 2 hours in each X, Y, Z direction at 10 to 55 Hz and with peak-to-peak amplitude of 1.5 mm (at power off)
Shock resistance Durability: 3 times at 500 m/s² (approx. 50 G) in each X, Y, Z direction
(at power off)
Protection rating IP65
Case material ABS (nut ABS/PC alloy resin)
Cable ø4, 3-core round cord of 0.2 mm² and 1 m in length (oil and heat resistant)
Weight Approx. 30 g

*For a detailed specification of the other, please refer to specifications.

External dimensions diagram / Output circuit

External dimensions diagram

MGP-C-501_en01

Output circuit

ST-MGP_C□501□kairo_EN.jpg

Usage precautions

  1. If there are magnetic objects on or around the installation location of the electromagnetic sensor, keep a distance between the sensor and these objects greater than the distance between the sensor and the magnet tape.
    Check also carefully the detection characteristics before using the sensor.
  2. If there is magnetic metal with residual magnetism in the surroundings of the electromagnetic sensor installation location,
    the detection characteristics may greatly vary. Verify the detection characteristics before using the sensor.
  3. Tighten the sensor using the nuts supplied with a torque of 0.5 Nm.
  4. See Electromagnetic sensor general usage precautions for other precautions.

 

Precautions with detection area diagram and reverse polarity flux

Precautions with detection area diagram and reverse polarity flux (typical example)

MGP-C-501_en03

Part number index

Product Comparison Table

confirmation of the estimate request content

Electromagnetic sensor

Go to page top