How It Works Shipping Fee Terms of Use

Model MDE-C10 Inductive Detection Sensor for All Metals

Application

  • It is possible to extend the detection distance even for non-magnetic metals such as aluminum and copper.
  • A detection distance of 8.5mm can be obtained with 1-yen coin (aluminum).
  • Any metal can be detected.
  • Maintenance is straightforward due to the connector type.

Features

  • Detection of brass, copper or aluminum coins such as those used in ATMs
  • Detection of vending machine coins and non-magnetic metal cans
  • Level detection of magnetic steel balls and non-magnetic metal balls
  • Detection of tokens

International Standards

  • Our products do not have overseas safety regulations such as CE mark, UL standard, EN standard etc.
  • Products is compliant to the RoHS directive.

* Please consult about "change of specification" and "request of specification" of the product.

Rating/Performance

Rating / Performance

Model MDE-C10 MDE-C10
Detection Surface Upper side detection
Detection Distance 10 mm ± 10 % (With detection target of Aluminium of 40 × 40 mm and 1 mm in thickness)
Set Distance 8.0 mm
Hysteresis 15 % or less of the detection distance
Power Supply Voltage 12 V to 24 V DC (Operating voltage range : 10.8 V to 26.4 V DC)
Current Consumption 15 mA DC or less
Output Nch MOSFET open drain 30 V DC, 100 mA DC or less
Output Residual Voltage 0.5 V DC or less (100 mA DC)
Operation Status Normally open (ON output when detecting) Normally closed (OFF output when detecting)
Response Frequency 400 Hz or more
Temperature Range -10 to 60 ºC (-25 to 65 ºC storage temperature range) (Without dew condensation or icing)
Humidity Range 85 % RH or less (85% RH or less storage humidity range) (without dew condensation)
Circuit Protection With reverse polarity connection protection diode, With output surge absorption diode
Dielectric Strength 500 V AC for 1 minute (Between the live part and case)
Insulation Resistance 50 MΩ or more at 500 V DC megger (Between the live part and case)
Vibration Resistance 10 to 55 Hz, 1.5 mm double amplitude in X, Y and Z directions for 2 hours each (at power off)
Shock Resistance 500 m/s² (Approx. 50 G) in X, Y and Z directions 3 times each (at power off)
Protection IP50
Case Material PBT resin (Blue)
Connecter Connector : S3B-PH-SM4-TB (3-pin) (from J.S.T. Mfg. Co., Ltd.)
[Connections]Housing : PHP-3, Contact: SPH-002T-P0.5S (from J.S.T. Mfg. Co., Ltd.)
Weight Approx. 15 g
Options
(Sold Separately)
Connector harness : CNH-PHR03S24-300

*For a detailed specification of the other, please refer to specifications.

Characteristics Graph

Change of detection distance depending on the size of the detection object (Typical)

検出体の大きさによる検出距離の変化EN_MDE-C10.jpgIf the detection object is smaller than the standard detection object or if it is made of non-ferrous metal, the detection distance will decrease.
Carry out testing to confirm suitability.

Change in detection distance depending on the detection object material (Typical)

ST-MDE-C10_EN_12.jpg

The detection distance will change according to the detection object material; carry out testing to confirm suitability.

Coin Detection Distance

ST-MDE-C10_EN_07_03.jpg

Detection Sistance of The Pachinko-slot Token (ø25 × t=1.6)

ST-MDE-C10_EN_07_07.jpg

Outline Dimensions/Connector Harness/Output Circuit

Outline Dimensions

ST-MDE-C10_EN_03.jpg

Connector Harness (Sold Separately)

CNH-PHR03S24-300_EN.gif

Output Circuit

ST-MDE-C10_EN_06.jpg

*Because there is no reverse connection protection diode built-in, pay careful attentionto the polarity of the power supply.

Precautions During Use

Influence of Surrounding Metal

If there are metals present near the inductive sensor,keep them away from and beneath the plane of the sensor
detection surface at a minimum of the values specified in the figure below.
 
MDE-C10_EN2_11.jpgUse the sensor carefully so as not to contact the front surface of the detection target.

Mutual Interference

When a number identical sensors are used,
observe the minimumvalues shown in the figure below to prevent mutual interference.
(The different frequency model type has “B” at the end of its model designationdesignation.)
相互干渉EN_MDE-C10.jpg

mounting

Always use plain washers to tighten the case and use a torque of 0.5 N·m or less.

Other

See inductive sensor general Precautions During Use for other precautions.

 

*After you have put an item in your shopping cart, choose either [Quote] or [Order].
*For customized products or specifications, contact us using "Inquiry."
*Choose the currency from JPY, USD, or EUR.

Model Name Operation Configuration Frequency Standard Price Inventory Type Select
MDE-C10 Normally open Normal type
58 USD
54 EUR
BTO
MDE-C10B Normally open Different frequency type
58 USD
54 EUR
STD
MDE-C101 Normally closed Normal type
58 USD
54 EUR
BTO
MDE-C101B Normally closed Different frequency type
58 USD
54 EUR
STD

STD Shipping is available immediately (on the day of order)

WIP Shipping is available within 1 to 3 weeks

BTO Shipping is available within 10 to 18 weeks

NOTE: The above information shows the typical delivery time. For actual delivery time, please confirm us as it depends on our business days and/or product quantities.

In the case of the quote request and order, please be sure to check the Terms and Conditions.
If you have made the procedure of quote request and order, it assumes that agree to the Terms and Conditions.

Quantity:
pieces
  • 1 USD
    1 EUR

To confirm the Request a quote / Order Cart

Part number index

Product Comparison Table

confirmation of the estimate request content

Proximity sensor

Go to page top