• センサ、タッチセンサの日本語ページ
  • sensor,touch sensor English site
How It Works Shipping Fee Terms of Use

Model HTS-30L Touch Sensor (Low Consumption Type)

Application

  • Touch switch for door knobs
  • Elevator switch
  • Touch switch for automatic doors
  • Touch switch for security purpose
  • Input switch for electric devices
  • Seat sensor
  • Input sensor of amusement equipment
  • Safety device for finger pinch avoidance from machine moving parts or door mechanisms

Features

  • This is a power-saving, low-power-consumption version which has a standby current of 30 μA or less,
    and therefore with battery power, has limitless placement possibilities.
  • The touch electrode can be set freely. Small type and equipped with a connector for easy installation and free positioning even in small places.
  • Does not operate by mistake when touched by an object with small electrostatic capacity such as plastic objects or bags.
  • Fixed sensitivity to avoid the need for troublesome settings.
  • Can withstand human static electricity without any external connection.
  • Does not use any contact point to prevent poor contact problems and leads to the long life.

International Standards

  • Our products do not have overseas safety regulations such as CE mark, UL standard, EN standard etc.
  • Products is compliant to the RoHS directive.

* Please consult about "change of specification" and "request of specification" of the product.

Rating and performance

Rating and performance

Model HTS-30L HTS-30L-4 HTS-30L-5 HTS-30L-6
Operation Sensitivity 30 pF ±6 pF 40 pF ±8 pF 50 pF ±9 pF 60 pF ±12 pF
Power Voltage 5 V  DC (Operating voltage range: 4.0 V to 6.5 V DC)
Standby Current Consumption Typ : DC 23 µA    Max : DC 30 µA (At 5 V DC)
Operation Power Consumption Typ : DC 44 µA    Max : DC 50 µA (At 5 V DC)
Output Nch MOSFET open drain 30 V DC, 50 mA DC or less
Output Residual Voltage 1 V DC or less (Load current 50 mA DC)
Operation Status On output with detection target
Temperature Range -20 to 60 °C (-25 to 65 °C during storage) (Without dew condensation or freezing)
Humidity Range 35 to 85 % RH (25 to 85 % RH during storage)
Anti-static Electricity ± 20 kV between the contact terminal and GND (500 pF, 500 Ω)
Breakdown Voltage 500 V AC, 50/60 Hz for 1 min (Between live parts and the case)
Insulation Resistance 20 MΩ or more, at 500 V DC megger (Between live parts and the case)
Vibration Resistance Durability : 10 to 55 Hz, Double amplitude: 1.5 mm in X-, Y-, and Z-direction, each 2 hours
(Device not powered)
Shock Resistance Durability : 500 m/s² (Approx. 50 G) in X-, Y-, and Z-direction, each 3 times (Device not powered)
Ingress Protection IP50
Case Material PBT reinforced with glass-fiber (Ivory)
Connector Connector : S4B-ZR (4-pin) (from J.S.T. Mfg. Co., Ltd.)
[Connections] Housing: ZHR-4, Contact: SZH-002T-P0.5 (from J.S.T. Mfg. Co., Ltd.)
Weight Approx. 2 g
Options
(Sold Separately)
Connector harness : SZH-4-300

 

Dimensions / Output circuit

Dimensions

HTS-30Z_Dimensions

Output circuit

HTS-30L_Output-Circuit *Because there is no reverse connection protection diode built-in, pay careful attention to the polarity of the power supply.

Usage precautions

  1. The touch (detection) electrode of the touch sensor is connected to the detection circuit.
    Therefore, it is necessary to ensure sufficient withstand voltage and insulation between the touch sensor power supply and the AC power supply to ensure safety.
  2. All conductors including the wire connected to the terminal No.4 of this sensor detect capacitance, so make them as short as possible,
    Separate from the wiring of the terminals No.1 to No.3 of this sensor so as not to pick up stray capacitance.
    Also, for the same reason, route the wiring for terminal No.4 as far as possible from all other conductors that are insulated from the wiring for this terminal.
    When passing through a restricted opening, where separation is difficult, use a spiral tube with a thickness of 1.5 mm or more of a material with a low relative dielectric constant of 3 or less and connect it to the wiring of the terminal No.4.
  3. If the sensor is used near a broadcasting station with high output, or if there is strong common-mode noise in the DC power supply because it is also used for a large inverter-fed device, install a capacitor of 0.1 μF or more to the 0 V line to remove the noise to the FG terminal.
  4. A high-frequency oscillation circuit is used in the touch sensor. Therefore, if several sensors get close or if the same person touches the touch lectrodes of several touch sensors at the same time, the detection operation may malfunction due to reciprocal interference. It is recommended to consult with our company since the interference depends on the position and wiring of the touch sensors and the sensor electrodes.
  5. The tightening torque for the case should be 0.3 N·m or less.
  6. For other precautions, refer to “General Precautions” for touch sensors.

*After you have put an item in your shopping cart, choose either [Quote] or [Order].
*For customized products or specifications, contact us using "Inquiry."
*Choose the currency from JPY, USD, or EUR.

Model Name Operating sensitivity Standard Price Inventory Type Select
HTS-30L 30 pF
670 JPY
7 USD
6 EUR
STD
HTS-30L-4 40 pF
670 JPY
7 USD
6 EUR
BTO
HTS-30L-5 50 pF
670 JPY
7 USD
6 EUR
STD
HTS-30L-6 60 pF
670 JPY
7 USD
6 EUR
STD

STD Shipping is available immediately (on the day of order)

WIP Shipping is available within 1 to 3 weeks

BTO Shipping is available within 4 to 10 weeks

NOTE: The above information shows the typical delivery time. For actual delivery time, please confirm us as it depends on our business days and/or product quantities.

In the case of the quote request and order, please be sure to check the Terms and Conditions.
If you have made the procedure of quote request and order, it assumes that agree to the Terms and Conditions.

Quantity:
pieces
  • 95 JPY
    1 USD
    1 EUR

To confirm the Request a quote / Order Cart

Go to page top